dieselspecialists.net / Shopdieselspecialists.com Diesel Forum

diagnostic service codes

Author Topic: diagnostic service codes  (Read 12014 times)

0 Members and 1 Guest are viewing this topic.

Offline Ram it

  • Guest
  • Posts: 1
  • Karma: +0/-0
    • View Profile
Re: diagnostic service codes
« Reply #8 on: July 05, 2007, 12:04:33 AM »
Have code po216 injection timing control circuit malfunction,any cure suggestions?Ramit

dieselspecialists.net / Shopdieselspecialists.com Diesel Forum

Re: diagnostic service codes
« Reply #8 on: July 05, 2007, 12:04:33 AM »

Your #1 Source for Diesel performance and Repair Parts.

Offline Kurt Lincoln

  • Service Manager/Owner
  • Diesel Forum Administrators
  • Diesel Technician (Master GearHead)
  • *****
  • Posts: 727
  • Karma: +85/-0
  • Gender: Male
    • View Profile
    • http://dieselspecialists.net
Re: Diagnostic code
« Reply #7 on: December 21, 2005, 10:03:28 AM »
Quote from: "Cumminshead"
I checked out the codes you have listed and cant figure out what the one i get means.  My truck is showing the P1689 code.  that doesn't state what actually is wrong? how do i figure it out.  truck started running poor, missing and bad idle, though rpm stayed steady,  truck shut off and can't get it restarted.  just installed a new FASS system to replace the lift pump. would it be the injection pump or just a relay with the code P1689? thanks
sounds like your injection pump is going out. was the old lift pump bad if so injection pump is right behind it :?:
Kurt Lincoln
Diesel Specialists Inc.
850 Susnshine Lane
Altamonte Springs, FL 32714
1-800-785-0775

dieselspecialists.net / Shopdieselspecialists.com Diesel Forum

Re: Diagnostic code
« Reply #7 on: December 21, 2005, 10:03:28 AM »

Your #1 Source for Diesel performance and Repair Parts.

Cumminshead

  • Guest
Diagnostic code
« Reply #6 on: December 11, 2005, 05:26:19 PM »
I checked out the codes you have listed and cant figure out what the one i get means.  My truck is showing the P1689 code.  that doesn't state what actually is wrong? how do i figure it out.  truck started running poor, missing and bad idle, though rpm stayed steady,  truck shut off and can't get it restarted.  just installed a new FASS system to replace the lift pump. would it be the injection pump or just a relay with the code P1689? thanks

Offline Kurt Lincoln

  • Service Manager/Owner
  • Diesel Forum Administrators
  • Diesel Technician (Master GearHead)
  • *****
  • Posts: 727
  • Karma: +85/-0
  • Gender: Male
    • View Profile
    • http://dieselspecialists.net
Re: diagnostic code P0122
« Reply #5 on: July 25, 2005, 09:55:33 AM »
Quote from: "ticketwhiz"
Is this a part that must be purchased at a dealer?
Also would this be covered in the Cummins warrenty?
I have 2002 4x4 quad-cab.
no you can buy it from us but check out your dealer for warrenty an save $$$.$$ 8)
Kurt Lincoln
Diesel Specialists Inc.
850 Susnshine Lane
Altamonte Springs, FL 32714
1-800-785-0775

ticketwhiz

  • Guest
diagnostic code P0122
« Reply #4 on: July 22, 2005, 06:48:13 AM »
Is this a part that must be purchased at a dealer?
Also would this be covered in the Cummins warrenty?
I have 2002 4x4 quad-cab.

Offline Kurt Lincoln

  • Service Manager/Owner
  • Diesel Forum Administrators
  • Diesel Technician (Master GearHead)
  • *****
  • Posts: 727
  • Karma: +85/-0
  • Gender: Male
    • View Profile
    • http://dieselspecialists.net
Re: Year
« Reply #3 on: March 15, 2005, 02:03:03 PM »
Quote from: "adam"
What year are these codes for?
1998-03 DODGE 5.9 CUMMINS :shock:
Kurt Lincoln
Diesel Specialists Inc.
850 Susnshine Lane
Altamonte Springs, FL 32714
1-800-785-0775

adam

  • Guest
Year
« Reply #2 on: March 10, 2005, 04:28:30 PM »
What year are these codes for?

Offline Kurt Lincoln

  • Service Manager/Owner
  • Diesel Forum Administrators
  • Diesel Technician (Master GearHead)
  • *****
  • Posts: 727
  • Karma: +85/-0
  • Gender: Male
    • View Profile
    • http://dieselspecialists.net
diagnostic service codes
« Reply #1 on: February 10, 2005, 02:47:13 PM »
DIAGNOSTIC SERVICE CODES      1998-03 DODGE CUMMINS    
    P0100-0199



(P0112)  CODE SET WHEN INTAKE AIR TEMP SENSOR CIRCUIT VOLTAGE AT (ECM)GOES BELOW
       0.098V FOR MORE THEN 2 SECONDS.
(P0113)  CODE SET WHEN INTAKE AIR TEMP SENSOR CIRCUIT VOLTAGE AT (ECM)GOES ABOVE
       4.97V FOR MORE THEN 2 SECONDS.
(P0117)  CODE SET WHEN ENGINE COOLANT TEMP (ECT) SENSOR CIRCUIT VOLTAGE AT (ECM)
       IS BELOW 0.80V FOR MORE THEN 2 SECONDS.
(P0118)  CODE SET WHEN ENGINE COOLENT TEMP (ECT) SENSOR CIRCUIT VOLTAGE AT (ECM)
       IS ABOVE 4.98V FOR MORE THEN 2 SECONDS.
(P0121)  CODE SET WHEN IDLE VALIDATION SWITCH (IVS) CIRCUITS INDICATE IDLE CONDITION
       WHILE ACCELERATOR PEDAL POSITION SENSOR (APPS) VOLTAGE INDICATE ABOVE IDLE.
(P0122)  CODE SET WHEN LOW VOLTAGE IS DETECTED AT ACCELERATOR PEDAL POSITION SENSOR
       (APPS) SIGNAL CIRCUIT AT (ECM).
(P0123)  CODE SET IF HIGH VOLTAGE IS DETECTED AT ACCELERATOR PEDAL POSITION SENSOR
       (APPS) SIGNAL CIRCUIT AT (ECM).
(P0125)  CODE SET IF ENGINE COOLANT TEMP DOES NOT INCREASE BY AT LEAST 18f or (10c)
       WITHIN 10 MINUTES OF ENGINE START-UP.
(P0168)  CODE SET WHEN INJECTION PUMP FUEL TEMP EXCEEDS PRE-DETERMINED LIMIT.
       ENGINE POWER IS REDUCED WHEN CODE SETS.
(P0177)  CODE SET IF (ECM)DETECTS WATER IN FUEL SYSTEM. WATER IN FUEL (WIF) SENSOR
       IS MOUNTED AT BOTTOM OF FUEL FILTER ASSEMBLY.
(P0178)  CODE SET WHEN LOW VOLTAGE DETECTED AT WATER IN FUEL (WIF) SENSOR SIGNAL
       CIRCUIT. MONITORED WITH IGNITION ON.
(P0180)  CODE SET WHEN INJECTION PUMP TEMP EXCEEDS PRE-DETERMINED LIMIT.CIRCUIT
       IS MON

DIAGNOSTIC SERVICE CODES    
    P0200-0299


(P0215)  CODE SET IF INJECTION PUMP RELAY DOES NOT CLOSE WHEN ACTUATED BY(ECM).
       CIRCUIT IS MONITORED WITH KEY ON.
(P0216)  CODE SET WHEN INJECTION PUMP TIMMING IS OUTSIDE EXPECTED RANGE FOR
       5 SECONDS OR LONGER.
(P0217)  CODE SET WHEN ENGINE COOLENT TEMP (ECT)SENSOR CIRCUIT VOLTAGE
       INDICATES EXCESSIVELY HIGH TEMP (BEYOND ENGINE PROTECTION LIMMITS).
(P0219)  CODE SET WHEN CRANKSHAFT POSITION (CKP)SENSOR INDICATES ENGINE SPEED
       HAS EXCEEDED OVERSPEED LIMITS.
(P0222)  CODE SET WHEN IDLE VALIDATION SWITCH (IVS)CIRCUITS 1&2 "ON" (CLOSED)
       AT SAME TIME.
(P0223)  CODE SET WHEN IDLE VALIDATION SWITCH (IVS)CIRCUITS 1&2 "OFF" (OPEN)
       AT SAME TIME.
(P0234)  CODE SET IF MANIFOLD AIR PRESSURE (BOOST)EXCEEDS PRE-DETERMINED LIMIT.
(P0236)  CODE SET IF BOOST (MAP) PRESSURE TEST FAILS OR IF ANY MAP SENSOR
       CIRCUITS OPEN OR SHORTED.
(P0237)  CODE SET WHEN MAP (BOOST)SENSOR SIGNAL VOLTAGE IS BELOW 0.10V FOR
       2 SECCNDS WITH ENGINE RUNNING.
(P0238)  CODE SET WHEN MAP (BOOST)SENSOR SIGNAL VOLTAGE IS ABOVE 4.88V AT
       START OR WITH ENGINE RUNNING FOR 2 SECONDS.
(P0251)  CODE SET IF INJECTION PUMP MODULE DOES NOT SENSE CHANGE IN CURRENT
       FLOW WHEN FUEL METERING VALVE IS ACTUATED.
(P0253)  CODE SET IF INJECTION PUMP MODULE SENSES INTERNAL FUEL METERING VALVE
       CIRCUIT IS OPEN.
(P0254)  CODE SET WHNE INJECTION PUMP MODULE DETECTS AN INTERNAL PUMP
       METERING VALVE FAILURE. ITORED WITH ENGINE RUNNING.
(P0181)  CODE SET WHEN INJECTION PUMP MODULE DETECTED AN INTERNAL PUMP FAILURE.


 DIAGNOSTIC SERVICE CODES
      P0300-0399


(P0300)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0301)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0302)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT  
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0303)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0304)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0305)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0306)  CODE SET WHEN TIME FOR CRANKSHAFT TO TURN 120' DURING CURRENT
       CYLINDER FIRING CYCLE DIFFERS FROM TIME OF PREVIOUS CYLINDER
       FIRING CYCLE.
(P0336)  CODE SET WHEN CRANKSHAFT POSITION (CKP)SENSOR INDICATES NO
       ENGINE SPEED OR POSITION SIGNAL TO (ECM).
(P0341)  CODE SET WHEN CAMSHAFT POSITION (CMP)SENSOR INDICATES NO ENGINE
       SPEED OR POSITION SIGNAL TO (ECM).
(P0370)  CODE SET WHEN INJECTION PUMP MODULE DETECTS LOSS OF INTERNAL PUMP
       SPEED SIGNAL.
(P0380)  CODE SET IF (ECM)DOES NOT SENSE CHANGE IN CURRENT FLOW WHEN INTAKE
       AIR HEATER RELAY #1 ACTUATED.
(P0381)  CODE SET WHEN "WAIT TO START" LAMP CIRCUIT OPEN OR SHORTED FOR 2
       SECONDS OR LONGER.
(P0382)  CODE SET IF (ECM)DOES NOT SENSE CHANGE IN CURRENT FLOW WHEN INTAKE
       AIR HEATER RELAY #2 ACTUATED.
(P0387)  CODE SET WHEN CRANKSHAFT POSITION (CKP)SENSOR INDICATES NO ENGINE
       SPEED OR POSITION SIGNAL TO (ECM).
(P0388)  CODE SET WHEN CRANKSHAFT POSITION (CKP)SENSOR INDICATES NO ENGINE
       SPEED OR POSITION SIGNAL TO (ECM).

DIAGNOSTIC SERVICE CODES
        P0500-0599

(P0522)  CODE SET WHEN (ECM)DETECTS OIL PRESSURE SENSOR VOLTAGE BELOW 0.10V.
(P0523)  CODE SET WHEN (ECM)DETECTS OIL PRESSURE SENSOR VOLTAGE ABOVE 4.90V.
(P0524)  CODE SET WHEN OIL PRESSURE DROPS BELOW MINIMUM OPERATING SPEC.
(P0562)  CODE SET WHEN BATT(+)VOLTAGE AT (ECM) IS BELOW 6.0V.CIRCUIT
       IS MONITORED WITH KEY ON.
(P0563)  CODE SET WHEN BATT(+)VOLTAGE AT (ECM)IS ABOVE 17.0V CIRCUIT IS
       MONITORED WITH KEY ON.



        P0600-0699

(P0602)  CODE SET IF (ECM) INTERNAL PARAMEETERS ARE OUT OF RANGE FOR 1
       SECOND. CIRCUIT MONITORED WITH IGNITION ON.
(P0606)  CODE SET WHEN (ECM)DETECTS AN INTERNAL FAILURE.


DIAGNOSTIC SERVICE CODES
       P1000-1999


(P1283)  CODE SET WHEN INJECTION PUMP MODULE DETECTS ERRONEOUS LOW IDLE
       SELECTSIGNAL FROM (ECM)CIRCUIT IS MONITORED FOR FAULT WITH KEY ON.
(P1284)  CODE SET WHEN FUEL INJECTION PUMP INTERNAL VOLTAGE CIRCUIT OUT
       OF RANGE.
(P1285)  CODE SET IF INJECTION PUMP MODULE STAYS "ON" WHEN (ECM)SWITCHES
       PUMP MODULE RELAY "OFF".
(P1286)  CODE SET WHEN HIGH VOLTAGE DETECTED AT ACCELERATOR PEDEL POSITION
       SENSOR (APPS) SUPPLY CIRCUIT.
(P1287)  CODE SET WHEN BATTERY VOLTAGE DROPS BELOW 5.50V WITH ENGINE RUNNING,
       OR BELOW 5.50V WITH ENGINE CRANKING.
(P1291)  CODE SET WHEN NO RISE IN INTAKE AIR TEMP DETECTED DURING FIRST 15
       SECONDS OF ENGINE OPERATION.
(P1295)  CODE SET WHEN LOW VOLTAGE IS DETECTED AT ACCELERATER PEDEL
       POSITION SENSOR (APPS)SUPPLY CIRCUIT.
(P1475)  CODE SET WHEN (ECM) AUX 5.00V OUTPUT IS ABOVE 5.50V.CIRCUIT IS
       MONITORED FOR FAULT WITH KEY ON.
(P1488)  CODE SETWHEN (ECM) AUX 5.00V OUTPUT IS BELOW 4.50V. CIRCUIT IS MONITORED
       FOR FAULT WITH KEY ON.
(P1688)  CODE SET WHEN INJECTION PUMP MODULE DETECTS INTERNAL PUMP FAILURE.
(P1689)  CODE SET WHEN INJECTION PUMP MODULE IS UNABLE COMMUNICATE WITH
       (ECM) FOR 3 SECONDS OR LONGER.
(P1690)  CODE SET WHEN INJECTION PUMP (CKP) SIGNAL &(ECM) (CKP) SIGNAL
       DISAGREE.
(P1691)  CODE SET WHEN INJECTION PUMP MODULE DETECTS AN INTERNAL PUMP
       CALIBRATION ERROR.
(P1693)  CODE SET WHEN (ECM) DETECTS CODE IN JTEC CONTROLLER (PCM).
(P1698)  CODE SET IF (ECM) DOES NOT RECEIVE (CCD) BUS MESSAGES FROM (PCM).
       POSSIBLE CAUSES ARE BUS (+) OR BUS (-) CIRCUITS OPEN, (ECM) BATTERY
       (-) OPEN OR FAULTY (PCM).
Kurt Lincoln
Diesel Specialists Inc.
850 Susnshine Lane
Altamonte Springs, FL 32714
1-800-785-0775

 

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 
Diesel Specialists Inc.